Scrap Trough, welded to dump sink (for 20" x 20" x 8" bowl Spec-line soil S30 series only) (sold per linear foot) (minimum 3 ft.) Maximum scrap trough length is 8 ft., (consult factory for trough lengths exceeding 8 ft.)
DTA-46
Inside mitered corner
DTA-55
Column notch (includes splash)
DTA-66
Provision for dish landing on straight dish table (sold per linear foot) (minimum 4 ft)
DTA-72
Provision for Side Loader
DTA-78
Notch backsplash return to accommodate dish machine interference (Please specify Dish Machine being used)
DTA-79
Double Sided Slant Tubular Rack Sorting Shelf, table mounted (sold per linear foot) (minimum 4 ft), field convertible to allow racks to sit back to back (steeper angle) or one side or the other (lower angle), see spec sheet for details
DTA-79S
Double Sided Slant Solid Base Rack Sorting Shelf, table mounted (sold per linear foot) (minimum 4 ft), (NOTE: Due to angle of racks, they will NOT fit back to back)
DTA-82
Dump Sink, mounted under dish table, 15" x 20" x 8" bowl, attaches to underside of dish table with legs supporting sink on floor (factory-prepared for field installation only)
DTA-84
Simple Pass-Thru (sold per linear foot) (minimum 3 ft)
DTA-87
Pass-thru window frame (sold per linear foot) (minimum 3 ft)
DTA-95
Installation, scrapper top (S914, P914, PRP & PRS, top by others)
Sink Bowl, 16"W x 20"D x 12" deep, welded into top, (per bowl) (must specify sink location)
DTA-99B
Sink Bowl, 20"W x 20"D x 12" deep, welded into top, (per bowl) (must specify sink location)
DTA-99C
Sink Bowl, 10"W x 14"D x 5" deep, welded into top, (per bowl) (must specify sink location)
DTA-99D
Sink Bowl, 18"W x 24"D x 14" deep, welded into top, (per bowl) (must specify sink location)
DTA-99E
Sink Bowl, 24"W x 24"D x 14" deep, welded into top, (per bowl) (must specify sink location)
K-23
Sink or dish table legs welded to cross rails (and optional undershelf if ordered), shipped set up and crated (per sink) Top is not welded to legs (for fully welded sink or dish table specify K-23A).
K-23A
Sink or dish table legs welded to leg gussets under table top and to cross rails (and optional undershelf if ordered), shipped set up and crated (per sink)
K-24
Shell crated
K-37
Anti-Siphon vacuum breaker holes
K-440
Waste trough, furnished with a 2" deep removable basket
K-453
Control Bracket, 14" x 16" (each)
K-454
Side splash, integral (welded), for NSF sinks & dish tables, height matches backsplash height (specify side)
K-456
Scrap BLock installed
K-460
Installation, disposal cone with 8" x 12" control bracket & faucet holes (each)
K-461
Install collar, with 8" x 12" control bracket
K-461A
Install collar, with 14" x 16" control bracket
K-472
Faucet hole revision (each)
K-495
Turn Down Backsplash (includes wall clips)
K-508A
Special modification for sinks & dish tables
K-57
Welded field joint (welded in field by others)
K-700D
Side splash, removable, for dish tables, 12" tall, reversible, stainless steel (fits either end) (must specify model to be installed on) (for other sinks use K-700)
