Advance Tabco Table Top Modifications

TA-1

Modify pass-thru shelf to accommodate roll-down door

$208

Details

TA-10

Partial backsplash, 5" high (per linear foot)

$94

Details

TA-100

Bullnose all sides of work table (nc)

Details

TA-100F

Bullnose front edge of dish cabinet

$155

Details

TA-101

Rear Tray Lock (per linear foot)

$130

Details

TA-106

Mirror Highlight work table upgrade

$581

Details

TA-107

Anti-Siphon vacuum breaker holes in splash, (2) holes, backsplash will be made 2" deep to accommodate (TA-11Z modification included)

$531

Details

TA-108

Punch 2" hole for appliance cord (specify location)

$191

Details

TA-112

Electric outlet, Hubble-Lock connector

$825

Details

TA-113

Notch table top for floor-mounted buyout equipment (for open base tables only-with undershelf, must also use TA-40)

$1192

Details

TA-12

Countertop edge, (per table. See TA-12A for marine edge on corner tables)

$934

Details

TA-12A

Countertop edge, Marine edge for KTMS series tables

$1300

Details

TA-22

Square edge table (nc)

Details

TA-28

Cut-Out for cold well, includes (2) louver hinged doors (per cut-out)

$2158

Details

TA-29

Capping Strip (per linear foot)

$92

Details

TA-3

Upgrade table understructure to stainless steel (per linear foot)

$79

Details

TA-30

Side Splash, 1-1/2" high (each)

$130

Details

TA-30A

Partial backsplash, 1-1/2" high (per linear foot)

$59

Details

TA-31

Side Splash, 5" high (each)

$242

Details

TA-32

Side Splash, 10" high (each)

$474

Details

TA-34

Top cut-out for drop in equipment (per cut-out)

$355

Details

TA-34A

Top cut-out for under-mounted equipment (per cut-out)

$596

Details

TA-35

Splash Cut Out

$257

Details

TA-366A

Reinforced understructure under table top (increases capacity of table top by 30%) (each)

$466

Details

TA-41

Cutting Board, 5/8", Poly-Vance, (per sq. ft.)

$131

Details

TA-502

Install Advance Tabco-brand drop-in unit work table top (TA-34 top cut out also required), (Hot food units also require TA-27 control panel), (NOTE-most jurisdictions will not allow a stainless drop-in sink in stainless steel countertop-see TA-11 for weld-in sinks), (To install drop-in units not provided by Advance Tabco, consult factory for pricing)

$773

Details

TA-503

Cut table & install recessed hand sink (7-PS-42, 7-PS-42A OR 7-PS-43) (must specify location)

$613

Details

TA-521

Drop-In Urn Trough, 1 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$216

Details

TA-522

Drop-In Urn Trough, 2 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$430

Details

TA-523

Drop-In Urn Trough, 3 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$647

Details

TA-524

Drop-In Urn Trough, 4 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$864

Details

TA-525

Drop-In Urn Trough, 5 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$892

Details

TA-526

Drop-In Urn Trough, 6 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$944

Details

TA-527

Drop-In Urn Trough, 7 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$1000

Details

TA-528

Drop-In Urn Trough, 8 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$1029

Details

TA-529

Drop-In Urn Trough, 9 ft. long x 4-3/4" wide x 1-1/4" deep (inside dimensions), includes louvered cover & drain, stainless steel (for field installation only) (for factory installation see TA-64)

$1091

Details

TA-550

NOTE: Installation of customer-supplied buy-out equipment is available at additional cost (use TA-551 for hot food wells) (installation cost is NOT included in this quote as shown) (contact factory for price)

Details

TA-551

Installation of customer-supplied hot food well (requires TA-34 or TA-34A top cut out)

$1152

Details

TA-56

5" tall NSF partition

$650

Details

TA-56A

18" tall NSF partition

$936

Details

TA-57

Welded field joint (welded in field by others) (each) (apply one charge for each "joint" required between 2 pieces)

$359

Details

TA-57A

Prepare for field bolting to adjoining piece (apply one charge for each "joint" required between 2 pieces)

$759

Details

TA-57B

Compressed Field Joint, mechanically joined fine line seam with specially designed hardware to clamp pieces together (for use when field welding is not an option) (apply one charge for each "joint" required between 2 pieces)

$1016

Details

TA-58

Step-down top to 24" working height (each)

$1603

Details

TA-64

Urn Trough, (factory installation only) (sold per linear foot)

$218

Details

TA-7

Partial backsplash, 10" high (per linear foot)

$111

Details

TA-75

Miter front corner of table (per corner)

$1040

Details

TA-76

Paint on sound deadening under top (supplements standard sound deadening under support channels) (each)

$746

Details

TA-79

Flour Trough, (factory installed only) (per linear foot)

$274

Details

TA-8

Column notch (includes box-out splash)

$1015

Details

TA-82

Scrap Chute, (6" dia. opening)

$350

Details

TA-84

Simple pass-thru, (per linear foot)

$921

Details

TA-87

Enclose back of splash (per linear foot)

$130

Details

TA-91

Poly retaining clips, (for stainless steel top table), includes TA-22 (per table)

$644

Details

TA-93

Wall Clips, (for 5" & 10" splash only) (per table)

$111

Details

TA-96A

Can Opener Provision for openers with bolt on base (customer to provide model number & location) (For locations on front or rear of worktables, TA-22 square edge (no charge) is required, TA-22 not required for locations on either end of table, TA-22 not required on tables with countertop edge, but TA-96C is required on these tables)

$309

Details

TA-96B

Can Opener Surface Mount Provision with 4" stainless steel Tube for openers without base (customer to provide model number & location)

$774

Details

TA-96C

Can Opener Spacer Plate Provision for use on tables with countertop edge (for openers with bolt-on base) (requires TA-96A)

$479

Details