Scrap Trough, welded to dump sink (for 20" x 20" x 8" bowl Spec-line soil S30 series only) (sold per linear foot) (minimum 3 ft.) Maximum scrap trough length is 8 ft., (consult factory for trough lengths exceeding 8 ft.)
DTA-46
Inside mitered corner
DTA-47
Corner turn guide bar for dish table, includes inside mitered corner (DTA-46)
DTA-49
Upgrade dishtable with 3-compartment sink (DTC-3 series) to 14 gauge
DTA-51
Pre-Rinse Slide Bar, for 18"W x 24"D fabricated sink bowls
DTA-52
Pre-Rinse Slide Bar, for 24"W x 24"D fabricated sink bowls
DTA-55
Column notch (includes splash)
DTA-56
Additional drainboard area on machine side (priced per linear foot)
DTA-58
Pre-Rinse Basket with Slide Bar, for 18"W x 24"D fabricated sink bowls, 18/304 stainless steel
DTA-59
Pre-Rinse Basket with Slide Bar, for 24"W x 24"D fabricated sink bowls, 18/304 stainless steel
DTA-64
Pre-Rinse Slide Bar, for 16"W x 20"D fabricated sink bowls
DTA-66
Provision for dish landing on straight dish table (sold per linear foot) (minimum 4 ft)
Provision for limit switch (limit switch by others)
DTA-76
Move pre-rinse sink to conform to dish machine requirements, specify dish machine (see compatibility chart for more information) (nc)
DTA-78
Notch backsplash return to accommodate dish machine interference (Please specify Dish Machine being used)
DTA-79
Double Sided Slant Tubular Rack Sorting Shelf, table mounted (sold per linear foot) (minimum 4 ft), field convertible to allow racks to sit back to back (steeper angle) or one side or the other (lower angle), see spec sheet for details
DTA-79S
Double Sided Slant Solid Base Rack Sorting Shelf, table mounted (sold per linear foot) (minimum 4 ft), (NOTE: Due to angle of racks, they will NOT fit back to back)
DTA-81
Leg Assembly, stainless steel with welded cross brace & stainless steel feet, for dishtables
DTA-82
Dump Sink, mounted under dish table, 15" x 20" x 8" bowl, attaches to underside of dish table with legs supporting sink on floor (factory-prepared for field installation only)
DTA-84
Simple Pass-Thru (sold per linear foot) (minimum 3 ft)
DTA-87
Pass-thru window frame (sold per linear foot) (minimum 3 ft)
DTA-88
Provision for table mounted solid sorting shelf (cantilevered from backsplash)
DTA-88-FLAT
Provision for table mounted (flat) solid sorting shelf (cantilevered from backsplash)
DTA-88-SLANT
Provision for table mounted (slant) solid sorting shelf (cantilevered from backsplash)
DTA-95
Installation, scrapper top (S914, P914, PRP & PRS, top by others)
Sink Bowl, 16"W x 20"D x 12" deep, welded into top, (per bowl) (must specify sink location)
DTA-99B
Sink Bowl, 20"W x 20"D x 12" deep, welded into top, (per bowl) (must specify sink location)
DTA-99C
Sink Bowl, 10"W x 14"D x 5" deep, welded into top, (per bowl) (must specify sink location)
DTA-99D
Sink Bowl, 18"W x 24"D x 14" deep, welded into top, (per bowl) (must specify sink location)
DTA-99E
Sink Bowl, 24"W x 24"D x 14" deep, welded into top, (per bowl) (must specify sink location)
K-23
Sink or dish table legs welded to cross rails (and optional undershelf if ordered), shipped set up and crated (per sink) Top is not welded to legs (for fully welded sink or dish table specify K-23A).
K-23A
Sink or dish table legs welded to leg gussets under table top and to cross rails (and optional undershelf if ordered), shipped set up and crated (per sink)
K-24
Shell crated
K-37
Anti-Siphon vacuum breaker holes
K-440
Waste trough, furnished with a 2" deep removable basket
K-452
Control Bracket 8" x 12" (each)
K-453
Control Bracket, 14" x 16" (each)
K-454
Side splash, integral (welded), for NSF sinks & dish tables, height matches backsplash height (specify side)
K-456
Scrap BLock installed
K-457
Replacement Rubber Scrap Block
K-460
Installation, disposal cone with 8" x 12" control bracket & faucet holes (each)
K-460A
Installation, disposal cone with 14" x 16" control bracket & faucet holes (each)
K-461
Install collar, with 8" x 12" control bracket
K-461A
Install collar, with 14" x 16" control bracket
K-472
Faucet hole revision (each)
K-495
Turn Down Backsplash (includes wall clips)
K-508
Modification to reduce length, start with next largest size then add "K-508" to model number for sinks & dish tables (nc)
K-508A
Special modification for sinks & dish tables
K-57
Welded field joint (welded in field by others)
K-76
Paint-on sound deadening under top (each)
K-77
Splash cutout for pipe chase (chase by others)
TA-1
Modify pass-thru shelf to accommodate roll-down door
